JC-TLOM600B Transmission Line Insulator Contamination Online Monitoring System

JC-TLOM600B Transmission Line Insulator Contamination Online Monitoring System

JC-TLOM600B transmission line insulator contamination online monitoring system, capable of real-time monitoring of insulator salt density, ash density, air temperature, and relative humidity in high-voltage operating environment, and sending the monitoring information to the remote monitoring center via GSM/CDMA/GPRS or 3G network , The monitoring software running in the monitoring center performs data storage and display, and calculates and analyzes various parameters to obtain the insulation level of the insulator.

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

High-voltage power transmission tower monitoring

Free consultation telephone:

0519-85851518

Message
Related Products

Product Details

JC-TLOM600B transmission line insulator contamination online monitoring system, capable of real-time monitoring of insulator salt density, ash density, air temperature, and relative humidity in high-voltage operating environment, and sending the monitoring information to the remote monitoring center via GSM/CDMA/GPRS or 3G network , The monitoring software running in the monitoring center performs data storage and display, and calculates and analyzes various parameters to obtain the insulation level of the insulator.

The system adopts solar panel + battery power supply mode, which is easy to install. After it is put into operation, the operation department can timely grasp the pollution status and development trend of insulators, and scientifically arrange maintenance time accordingly, effectively prevent line pollution flashover accidents, reduce economic losses, and improve line safety operation and information management level.

Salt density measurement range: 0mg/cm2～1.0mg/cm2; accuracy: ±10%;

Ash density measurement range: 0mg/cm2～2.0mg/cm2; accuracy: ±10%;

Temperature measurement range: -40℃～+120℃; measurement accuracy: ≤±0.5℃;

Humidity measurement range: 0～100%RH; measurement accuracy: ≤±3%RH;

Working environment: temperature: -40℃～+85℃; relative humidity: ≤100%; atmospheric pressure: 550hPa～1060hPa;

Protection level: IP65;

Working power consumption: ≤2W; standby power consumption ≤0.5W;

Power supply mode: solar + battery, input voltage +12～24V;

Battery life: ≥3 years, continuous power supply for more than 30 days without external charging;

MTBF: ≥80,000 hours;

Weight: ≈10kg;

Applicable objects: 10KV~500KV high voltage transmission lines.

Related Products

Maintenance-free intelligent transformer breather

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.
JC-OM700-EE Wireless Expansion Joint Sensor

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.
Current monitoring sensor of arrester in switchgear

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485
Ground resistance sensor

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω  Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54
High frequency current sensor

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping
Tilt sensor

Tilt sensor

Range: ± thirty °  Voltage: 9-35v Output mode: RS485 IP67 protection level
Infrared thermal imaging camera of switch cabinet

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)
Space UHF PD sensor

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years
Micro weather sensor

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S
Switch cabinet partial discharge sensor (UHF)

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)
Switch cabinet partial discharge sensor (UHF + AE two in one)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge
Intelligent air conditioning / dehumidification linkage device

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability

Welcome your message consultation

Our staff will contact you within 24 hours (weekdays), if you need other services, please call the service hotline:0519-85851518
Submit

Personalized smart device manufacturer

We can provide you with satisfactory customized service

Submit
%{tishi_zhanwei}%