智能巡检机器人-Jiangsu jotry Electric Technology Co., Ltd.

智能巡检机器人

智能巡检机器人主要用于电力隧道或变配电室进行日常巡检工作，通过铺设铝合金轨道，机器人能够快速稳定的运行在环境复杂的隧道中，搭载高清的相机及热成像镜头，对关键巡检点进行定时的巡查，同时搭载有害气体、烟雾及温湿度传感器，能够时刻监控隧道环境数据。

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

电缆隧道综合监控系统

Free consultation telephone:

0519-85851518

Message

隧道综合监控系统/综合管廊监控系统—智能巡检机器人

产品介绍

隧道智能巡检机器人主要用于电力隧道或变配电室进行日常巡检工作，通过铺设铝合金轨道，机器人能够快速稳定的运行在环境复杂的隧道中，搭载高清的相机及热成像镜头，对关键巡检点进行定时的巡查，同时搭载有害气体、烟雾及温湿度传感器，能够时刻监控隧道环境数据。

系统具备：刀闸变位、开关及指示灯状态识别，红外智能测温，环境智能监控与安防报警，仪表读数识别，噪声监测，空间局放检测。

系统特点

1）轨道式安装

高强度铝合金轨道

最小转弯半径1500mm

最大巡检速度2.5m/s

机身重量45kg

最大支持10000个巡检点

隧道机器人.jpg

2）红外热成像诊断

具备监测电缆温升检测、设备异常发热检查及着火点定位功能。当出现火情时，机器人能够迅速到达火情位置，并且能够根据区域温度特征快速的定位着火点位置

3）与智能运维管理平台的衍生衔接

控制中心大屏无缝对接

图像数据实时回传

声光报警系统

机器人集中任务管理

历史数据分析回放

<strong><strong>隧道智能巡检机器人</strong></strong> 2.png

Related Products

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability