无线SF6+O2气体检测器-Jiangsu jotry Electric Technology Co., Ltd.

无线SF6+O2气体检测器

气体检测器包括六氟化硫检测单元、氧气检测单元、温度测量单元和通信单元，对六氟化硫的检测运用超声波（可选配激光红外）检测技术克服了使用寿命短、稳定性差等缺点；氧气检测单元采用英国进口传感器，测量精度高、性能稳定；温度测量部分采用数字输出的温度模块，具有精度高、重复性好等特点。综上所述，无线SF6+O2气体探测器可实时、在线监测环境中SF6气体浓度、氧气含量以及温度的变化，将检测到的数据通过LoRa无线通讯进行上传。

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

配电物联网协议无线传感器

Free consultation telephone:

0519-85851518

Message

无线SF6+O2气体检测器

产品概述

气体检测器包括六氟化硫检测单元、氧气检测单元、温度测量单元和通信单元，对六氟化硫的检测运用超声波（可选配激光红外）检测技术克服了使用寿命短、稳定性差等缺点；氧气检测单元采用英国进口传感器，测量精度高、性能稳定；温度测量部分采用数字输出的温度模块，具有精度高、重复性好等特点。综上所述，无线SF6+O2气体检测器可实时、在线监测环境中SF6气体浓度、氧气含量以及温度的变化，将检测到的数据通过LoRa无线通讯进行上传。

无线SF6+O2.jpg

技术参数

☆ SF₆气体浓度测量范围： 0～3000μV/V（ppm）优于50μV/V

☆ SF₆气体监测灵敏度： 50μV/V（ppm）

☆ 氧气范围：0～25% 精度：±1%

☆ 氧气灵敏度：0.1%

☆ 温度范围：-40～＋125℃ 精度：±1%

☆ 温度灵敏度：0.1℃

☆ 工作电源：DC24V

☆ 通信接口：无线LoRa通讯

☆ 外型尺寸为：151mm×163mm×38mm

Related Products

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability