特高频局放探测器JC-OM400-03W

特高频局放探测器是能实时快速确定潜伏局部放电缺陷电力设备的装置。让电力用户只对隐患设备进行详细检测，大大减轻电力运维人员的检测工作量，有效避免电网设备安全事故发生。

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

无线LoRa传感器

Free consultation telephone:

0519-85851518

Message

特高频局放探测器

系统概述

变配电站设备出现故障的概率是很小的，大部分都是良好设备，目前对变电站逐个设备进行故障检测的方法，工作量非常大，且绝大部分工作都没有针对性，无用功较多。

特高频局放探测器是能实时快速确定潜伏局部放电缺陷电力设备的装置。让电力用户只对隐患设备进行详细检测，大大减轻电力运维人员的检测工作量，有效避免电网设备安全事故发生。

系统特点

♦安装简单，非接触，远距离监测，不对设备造成影响。

♦一次性投入，总体造价低。

♦跟人工检测形成互补，减少因长周期巡检带来的隐患。

技术参数

1、空间传感器

空间传感器.png

空间传感器安装实物图：

局放传感器.jpg

2、数据采集终端

数据采集终端实物图：

无线特高频空间局放传感器1.jpg

● 工作电源

采用AC/DC220V供电，允许偏差-20%～+20%。

● 结构

结构防护等级满足IP40防护等级要求，采用螺钉或卡扣安装。

● 技术参数

a) 检测频带：300MHz～2000MHz（500MHz-1500MHz）；

b) 系统灵敏度：≤17.6dBV/m；

c) 动态范围：≥60dB；

d) 系统测量范围：-80～-20 dBm；

e) 误差值：±2dBm；

f) 额定功率：≤35w；

g) 使用年限：≥5年。

h) IP等级：不低于IP40。

● 通信要求

a) 通信方式：同时支持无线及有线通信方式，无线通信采用基于LoRa的470MHz频段无线通信，满足输变电设备物联网节点设备无线组网协议，有线通信传输采用modbus协议传输。

b) 传输距离：大于50米；

c) 数据上送内容及频率：内容按标准格式，一小时采集一次，每次1s。

Related Products

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability