智能门锁JC-MS-ZN03

用高性能工业级CPU，主频可以达到100MHz。能够满足各种出入口控制系统的需要,具有防死机软件狗电路、自检电路和实时时钟电路设计，所有输入口光藕隔离，所有继电器输出带有瞬间过压保护，增强了控制器的稳定性和实时性。工业级设计，可每天24小时连续运行。

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

无线LoRa联动装置

Free consultation telephone:

0519-85851518

Message

智能门锁

产品概述

JC-MS-ZN03智能门锁采用高性能工业级CPU，主频可以达到100MHz。能够满足各种出入口控制系统的需要,具有防死机软件狗电路、自检电路和实时时钟电路设计，所有输入口光藕隔离，所有继电器输出带有瞬间过压保护，增强了控制器的稳定性和实时性。工业级设计，可每天24小时连续运行。

<strong><strong>门禁控制器</strong></strong>图.jpg

产品特点

1、可控制单门/双门/四门;

2、支持wiegand26/34接口的读卡器、指纹等生物识别读卡器;

3、所有I/O端口都有过压保护;

4、输出继电器接口常开/常闭可选;

5、大电流继电器输出接口，可驱动任何种类门锁;

6、支持刷卡，卡+密码、纯密码等各种开门方式;

7、提供有紧急开启和紧急锁闭功能，提高安全性并符合消防要求;

8、控制器可以直接外接有源或者无源报警器，不需要另外配置扩展板，降低了客户投入提高了系统稳定性;

9、系统具有防潜回、远程开门、多卡开门等高级门禁功能;

10、支持TCP/IP以及串口等通信方式;

技术参数

● 工作电源

a) 智能锁体部分采用电池供电或DC12V供电，优先采用DC12供电；

b) 无线通信部分采用DC12V。

c) 宜从直流屏取电，确保智能锁具正常工作。

● 结构

IP40防护等级，采用螺钉或卡扣安装。

● 技术参数

a) 执行标准：GB21556-2008《锁具安全通用技术条件》、JG/T394-2012《建筑智能门锁通用技术要求》；

b) 应具备授权密码开锁和远程开锁功能;

c) 使用年限：≥10年（不含门锁电池）。

● 通信

a) 通信方式：采用基于LoRa的470MHz频段无线通信，满足输变电设备物联网节点设备无线组网协议。

b) 无线传输距离：大于50米；

a) 数据上送频率：出厂配置1次/15分钟，可配置范围1次/分钟至1次/60分钟。门锁状态变化、开关门记录信息实时上送，控制信息配合网关实时执行，延时不超过5s。

产品通过国网电科院权威检测

Related Products

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability