避雷器泄漏电流数字化远传表计-Jiangsu jotry Electric Technology Co., Ltd.

避雷器泄漏电流数字化远传表计

该产品可实现金属氧化锌避雷器绝缘性能的监测，一台MOA用于采集1相避雷器的泄露电流及雷击次数。

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

变电物联网协议无线传感器

Free consultation telephone:

0519-85851518

Message

避雷器泄漏电流数字化远传表计

产品概述

表计式避雷器在线监测器主要有取样阀片、硅桥式整流器、高压电容器、电磁计数器、毫安表等元件组成。它是利用通过避雷器的放电电流，在阀片（非线性电阻）上产生的电压，经硅桥式整流对电容器充电，向电磁计数器放电，每放一次记录一次，来实现记录避雷器的动作次数。

避雷器在线监测器采用数字式显示，该显示具有指示清晰，便于观察等优点；计数循环次数为0～99每100次一个循环，这有利于将短期内通过避雷器的雷电次数较完整的记录下来。

避雷器在线监测器是串联在避雷器下面，既可用来记录避雷器动作次数，同时又可以通过毫安表监测避雷器在运行电压下的泄露电流的一种装置。用于330KV及以下等级的避雷器，使用地点的环境条件与相连的避雷器相同，它不适于有严重污秽和有剧烈震动的地方；采用氧化锌阀片，电气性能有较大提高。

系统架构图

技术参数

1.全电流测量范围： 0mA～3mA，测量精度±1%或10μA

2.雷击次数记录：0～99

3.数据通信：无线LoRa通讯，网络速率为：≤9600bps

工作环境

1．适用于户内或户外。
2．环境温度（-40～+40）℃。
3．海拔高度不超过2000m。
4．电源频率（48～62）Hz。
5．无剧烈震动场所。

Related Products

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability