无线智能门锁-Jiangsu jotry Electric Technology Co., Ltd.

无线智能门锁

无线智能门锁采用高性能工业级CPU，主频可以达到100MHz。能够满足各种出入口控制系统的需要,具有防死机软件狗电路、自检电路和实时时钟电路设计，所有输入口光藕隔离，所有继电器输出带有瞬间过压保护，增强了控制器的稳定性和实时性。工业级设计，可每天24小时连续运行。

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

配电物联网协议无线传感器

Free consultation telephone:

0519-85851518

Message

无线智能门锁

产品概述

<strong>门禁控制器</strong>图.jpg

产品特点

1、可控制单门/双门/四门;

2、支持wiegand26/34接口的读卡器、指纹等生物识别读卡器;

3、所有I/O端口都有过压保护;

4、输出继电器接口常开/常闭可选;

5、大电流继电器输出接口，可驱动任何种类门锁;

6、支持刷卡，卡+密码、纯密码等各种开门方式;

7、提供有紧急开启和紧急锁闭功能，提高安全性并符合消防要求;

8、控制器可以直接外接有源或者无源报警器，不需要另外配置扩展板，降低了客户投入提高了系统稳定性;

9、系统具有防潜回、远程开门、多卡开门等高级门禁功能;

10、支持TCP/IP以及串口等通信方式;

技术参数

项目		内容
电气参数	开关电源功率	根据需要可选（12V3A、12V5A、12V7A、12V10A）
	电路板功耗	12VDC 小于100mA
	输出继电器负载电流	12V/7A （必须配备相对应的电源）
	报警器	可外接有源或无源报警器
通信参数	读卡器输入格式	Wiegand 26/34 (兼容该协议下的HID、EM、Mifare1以及手机卡等读卡器)
	读卡距离	5－8cm
	读卡器到控制器最大联机距离	120米，建议100米内。
	通信接口	RS485
	控制器到PC机最大联机距离	RS485不小于1000米，TCP无限制
环境参数	储存温度	-10℃to +65℃
	储存湿度	10% to 90% RH
	工作温度	-35℃至 65℃
	工作湿度	10-90％RH，无冷凝

Related Products

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability