定位式漏水检测器-Jiangsu jotry Electric Technology Co., Ltd.

定位式漏水检测器

定位式漏水检测器是一款高性能的液体泄漏检测设备，它可以检测水或弱酸、弱碱等液体的泄漏，模块监控线缆长达 200 米，一旦检测到液体泄漏，则通过显示屏显示泄漏位置并输出继电器触点信号。模块既可作为单独运行的泄漏检测报警单元使用，也可与其它模块联网使用。

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

常规配电物联网传感器

Free consultation telephone:

0519-85851518

Message

定位式漏水检测器

产品概述

定位式漏水检测器是一款高性能的液体泄漏检测设备，它可以检测水或弱酸、弱碱等液体的泄漏，模块监控线缆长达 200 米，一旦检测到液体泄漏，则通过显示屏显示泄漏位置并输出继电器触点信号。模块既可作为单独运行的泄漏检测报警单元使用，也可与其它模块联网使用。模块可通过多种标准通讯协议与其它主监控系统、或其它上位机进行通信，以实现远程报警及远程设备的控制。模块可用基于微软Windows.的 PC 进行配置，模块自带有独立的配置软件。

典型应用系统图

1634199513(1).png

应用范围

此控制器适于整合入中央监控系统中，典型应用包括对空气处理装置、冷冻机械、液体容器、泵槽等设备或其它采用传感线缆的地点进行泄漏监控。连接不同类型的感应线缆，还可实对酸、碱、油等液体泄漏的检测监控。

技术参数

检测线缆：四芯定位检测线缆

检测线缆长度：最大可接线缆长度为 200 米

塑料外壳：白色 PVC,NEMA1,IP55

重量：385 克(0.85 磅)

精确度：检测线缆长度的 1%

响应时间：小于 1 秒

电源要求：24VAC/220VAC可选交流电源

继电器输出：1SPDT,60VDC 或 125VAC,1A 额定值(常开常闭)

通讯协议：RS485 串行接口(双线网络),MODBUS 通讯协议

Related Products

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability