O3传感器JC-O3-ZN03

O3传感器采用进口传感器，测量精度高，支持无线信号传输，输出性能稳定，使用寿命长，硬件设计上采用先进的单片微机，减少外围部件，提高系统的可靠性和稳定性。

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

无线LoRa传感器

Free consultation telephone:

0519-85851518

Message

O3传感器

产品概述

O3传感器采用进口传感器，测量精度高，支持无线信号传输，输出性能稳定，使用寿命长，硬件设计上采用先进的单片微机，减少外围部件，提高系统的可靠性和稳定性。

产品特点

1、实时监测环境臭氧值

2、采用进口传感器，测量精确可靠

3、支持无线LoRa通讯（470MHz或2.4GHz）

4、抗干扰性强

5、安装灵活方便

技术参数

● 工作电源

根据买方要求以下供电方式二选一：

a) 采用电池供电，电池容量不低于1200mAh，且在1次/15分钟频次下正常工作5年以上；

b) 采用AC/DC220V供电，允许偏差-20%～+20%。

● 结构防护等级

满足IP40防护等级要求，采用螺钉或卡扣安装。

● 技术参数

a) O3测量范围：0～20ppm；

b) O3精度：<±0.1ppm(25℃)；

c) 使用年限：≥5年。

● 通信

a) 通信方式：采用基于LoRa的2.4GHz频段无线通信，满足输变电设备物联网微功率无线网通信协议。或者采用基于LoRa的470MHz频段无线通信，满足输变电设备物联网节点设备无线组网协议。

b) 无线传输距离：大于50米；

c) 数据上送频率：数据上送频率：出厂配置1次/15分钟，可配置范围1次/分钟至1次/60分钟。

产品通过国网电科院权威检测

Related Products

Maintenance-free intelligent transformer breather

The maintenance-free transformer breather is an air dehumidification and purification device used for oil-immersed transformers, instrument transformers, on-load tap changers, or other electrical equipment filled with insulating liquid. The maintenance-free transformer breather is installed at the air inlet of the instrument transformer's oil storage tank. When the transformer or instrument transformer operates, the oil volume changes due to temperature variations, causing the gas inside the oil storage tank to breathe through the desiccant. Air passes through the filter at the bottom of the desiccant and the glass jar filled with silica gel into the transformer, ensuring that the inhaled air is dry (moisture is adsorbed by the desiccant) and clean (dust and impurities are blocked by the filter), thereby maintaining the cleanliness and insulation strength of the transformer oil.

JC-OM700-EE Wireless Expansion Joint Sensor

The JC-OM700-EE wireless expansion joint sensor achieves online monitoring of expansion joint compensation by modifying the existing mechanical vernier caliper of GIS/GIL expansion joints or adding a digital expansion joint displacement sensor. The wireless expansion joint sensor uses a high-speed ARM chip as the main controller and a high-precision displacement sensor to sample and calculate the displacement data of the measured object in real time. It can upload data to the host computer via wireless LoRa and wired RS485.

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability