Tower Beidou Differential Positioning System

The system uses wireless communication technologies such as differential GPS/Beidou technology, GPRS/3G/4G and LORA to realize remote monitoring of the attitude of the tower line. The operation and maintenance personnel can understand the settlement/displacement/deformation of the tower anytime and anywhere, which can be used for daily operation and maintenance. It is convenient to come and improves work efficiency.

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Free consultation telephone:

Product Details

The system uses wireless communication technologies such as differential GPS/Beidou technology, GPRS/3G/4G and LORA to realize remote monitoring of the attitude of the tower line. The operation and maintenance personnel can understand the settlement/displacement/deformation of the tower anytime and anywhere, which can be used for daily operation and maintenance. It is convenient to come and improves work efficiency.

This system is easy to install and has high measurement accuracy. Once data is found to be abnormal, the monitoring system can notify relevant personnel to deal with it in time through warning lights, siren, SMS, WeChat, etc.

The system can also be used to monitor wire galloping and wire sag.

Support high-precision positioning of the whole system and all frequency points: GPS L1, L2; BDS B1, B2; GLONASS G1, G2

Positioning accuracy: H: ±5mm; V: ±20mm

Start-up time: <30S

Communication working frequency band: full Netcom, seven frequency bands, support LTE-TDD/LTE-FDD/HSPA+/TD-SCDMA/

EVDO/GSM/GPRS/EDGE and other frequency bands

Data transmission LTE CAT4 Maximum uplink rate: 50Mbps, maximum downlink rate: 150Mbps

kbit/s;

Support TCP/IP, FTP, HTTP protocol

Power supply mode: DC12V

Working temperature: -40 ~ +85℃

Applicable objects: power towers, mobile communication base stations

Related Products

Current monitoring sensor of arrester in switchgear


Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor


Power supply: dc6 ~ 12V Range: 0.01 Ω- two hundred Ω  Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor


Sensitivity: 5pc Detection frequency band: 50KHz ~ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor


Range: ± thirty °  Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet


Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor


Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor


Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C; two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)


The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)


The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device


AC / dc220v power supply is adopted Allowable deviation - 20% ~ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability

Intelligent light control unit


Output mode: switch type, realize local and remote control of lighting Wall mounted / 2U rack mounted Using brand devices to ensure reliability Size (mm): 480mm long × 85mm wide × 340mm deep

Intelligent water pump control unit


Output mode: switch type, realize the linkage control of water pump Wall mounted / 2U rack mounted, Using brand devices to ensure reliability Size (mm): 480mm long × 85mm wide × 340mm deep

Welcome your message consultation

Our staff will contact you within 24 hours (weekdays), if you need other services, please call the service hotline:0519-85851518