JC-MJ-ZN01 Access Control System

Can control single door/double door/four door Support wiegand26/34 interface card reader, fingerprint and other biometric card reader All I/O ports have overvoltage protection Output relay interface normally open / normally closed optional High current relay output interface, which can drive any kind of door lock Support various door opening methods such as swiping card, card + password, pure password, etc.

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Free consultation telephone:

Product Details

Can control single door/double door/four door

Support wiegand26/34 interface card reader, fingerprint and other biometric card reader

All I/O ports have overvoltage protection

Output relay interface normally open / normally closed optional

High current relay output interface, which can drive any kind of door lock

Support various door opening methods such as swiping card, card + password, pure password, etc.

Provide unique emergency opening and emergency locking functions to improve safety and meet fire protection requirements

The controller can be directly connected to an active or passive alarm, no additional expansion board is required, which reduces customer input and improves system stability

The system has advanced access control functions such as anti-sneak-back, remote opening, and multi-card opening

Support communication methods such as TCP/IP and serial port

Switching power supply power: optional according to needs (12V3A, 12V5A, 12V7A, 12V10A)

Circuit board power consumption: 12VDC less than 100mA

Output relay load current: 12V/7A (must be equipped with corresponding power supply)

Alarm: an external active or passive alarm can be connected

Card reader input format: Wiegand 26/34 (compatible with HID, EM, Mifare1 and mobile phone card readers under this protocol)

Card reading distance: 5-8cm

The maximum online distance between the card reader and the controller: 120 meters, recommended within 100 meters.

Communication interface: RS485

Maximum connection distance between controller and PC: RS485 is not less than 1000 meters, TCP unlimited

Storage temperature: -10℃to +65℃

Storage humidity: 10% to 90% RH

Working temperature: -35℃ to 65℃

Working humidity: 10-90%RH, non-condensing

Related Products

Current monitoring sensor of arrester in switchgear


Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor


Power supply: dc6 ~ 12V Range: 0.01 Ω- two hundred Ω  Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor


Sensitivity: 5pc Detection frequency band: 50KHz ~ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor


Range: ± thirty °  Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet


Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor


Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor


Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C; two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)


The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)


The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device


AC / dc220v power supply is adopted Allowable deviation - 20% ~ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability

Intelligent light control unit


Output mode: switch type, realize local and remote control of lighting Wall mounted / 2U rack mounted Using brand devices to ensure reliability Size (mm): 480mm long × 85mm wide × 340mm deep

Intelligent water pump control unit


Output mode: switch type, realize the linkage control of water pump Wall mounted / 2U rack mounted, Using brand devices to ensure reliability Size (mm): 480mm long × 85mm wide × 340mm deep

Welcome your message consultation

Our staff will contact you within 24 hours (weekdays), if you need other services, please call the service hotline:0519-85851518