JC-SW-ZN01 water level sensor_Jiangsu jotry Electric Technology Co., Ltd.

JC-SW-ZN01 water level sensor

The water level sensor uses a high-performance pressure-sensing chip, combined with advanced circuit processing and temperature compensation technology, to convert pressure changes into linear current or voltage signals. The product is small in size and easy to install. It uses a stainless steel shell to isolate and anti-corrosion. It is suitable for measuring media such as gases and fluids that are compatible with the material of the contact part. It can be used to measure gauge pressure, negative pressure and absolute pressure. The water level sensor is based on the prototype of the universal pressure transmitter and is formed by adding a welded sealed isolation diaphragm structure. Its welded and sealed isolation diaphragm device has a variety of different process connection structures, which is especially suitable for pressure measurement in high temperature, high viscosity, crystalline media and easily clogged occasions, and also suitable for water level measurement in power environment, sanitation, and medical occasions.

Keyword:

Power IoT sensors Smart power distribution Internet of Things Smart cable tunnel gallery Smart power generation Internet of Things Smart Internet of Things

Category:

Other IoT sensors

Free consultation telephone:

0519-85851518

Message

Related Products

Product Details

The water level sensor is based on the prototype of the universal pressure transmitter and is formed by adding a welded sealed isolation diaphragm structure. Its welded and sealed isolation diaphragm device has a variety of different process connection structures, which is especially suitable for pressure measurement in high temperature, high viscosity, crystalline media and easily clogged occasions, and also suitable for water level measurement in power environment, sanitation, and medical occasions.

Measuring range: -0.1~100Mpa (optional)

Measurement accuracy: 0.2%, 0.5%

Output signal: 4~20mA, 0~5VDC, 0~10VDC, RS485

Overload capacity: <1.5 times the range

Temperature drift: 0.03%FS/℃

Power supply: 12~36VDC typical 12V (power consumption:)

Medium temperature: -20~75℃

Environment temperature: -30℃~80℃

Measuring medium: gas, liquid that does not corrode stainless steel

Measuring range: 0.5-300M (optional)

Measurement accuracy: 0.2%, 0.5% (optional)

Output signal: 4~20mA, O~5VDC, 0~10VDC

Overload capacity: <1.5 times the range

Power supply: 12~36VDC, typical 12V (power consumption:)

Temperature drift: 0.03%FS/℃

Environment temperature: -30℃~80℃

Medium temperature: -20~75℃

Measuring medium: liquid that does not corrode stainless steel and cables

Related Products

Current monitoring sensor of arrester in switchgear

Full current measurement range: 0.050 ~ 5.000mA Full current measurement error: ± (standard reading ×1%+5μA) Record the cumulative discharge times :0 ~ 99 times Power supply: DC24V Communication interface: RS-485

Ground resistance sensor

Power supply: dc6 ～ 12V Range: 0.01 Ω- two hundred Ω Accuracy: ± 2%rdg ± 3dgt(20℃ ± 5 ℃, below 70% RH) Communication mode: RS485 Protection grade: IP54

High frequency current sensor

Sensitivity: 5pc Detection frequency band: 50KHz ～ 100MHz Signal output: RS485 Installation position: cable connector ground wire Installation mode: clamp type, clamping

Tilt sensor

Range: ± thirty ° Voltage: 9-35v Output mode: RS485 IP67 protection level

Infrared thermal imaging camera of switch cabinet

Thermal imaging resolution: 160 * 120 Visible light resolution: 200W Power supply: dc12-24 V Temperature range: - 20 ℃ ~ 150 ℃ Accuracy: ± 2 ℃ or 2% of the reading (take the maximum absolute value)

Space UHF PD sensor

Detection frequency band: 300 ~ 1500mhz Protection grade: IP65 Collect the discharge amplitude and phase The service life is more than 8 years

Micro weather sensor

Temperature: measuring range - 40 ~ 60 ℃ ° C Accuracy ± zero point one ° C； two Temperature: measurement range 0 ~ 100% RH Air pressure: measuring range: 10 ~ 1300 Wind speed measurement range: 0-75 M / S

Switch cabinet partial discharge sensor (UHF)

The system adopts UHF principle to conduct local discharge monitoring of high voltage switchgear to ensure the effective monitoring data, and increase system reliability. Ultra low power consumption and 485 bus communication mode are adopted. It is applicable to switch cabinet and ring network cabinet. Each cabinet is equipped with one set to realize the power / qualitative measurement of local discharge. It can be directly connected to the system host without the limitation of host channel.)

Switch cabinet partial discharge sensor (UHF + AE two in one)

The system adopts UHF + AE principle Ultra low power consumption and 485 bus communication mode are adopted, It is suitable for switch cabinet and ring main unit to realize the quantity / qualitative measurement of partial discharge

Intelligent air conditioning / dehumidification linkage device

AC / dc220v power supply is adopted Allowable deviation - 20% ～ + 20% Control output node capacity: AC / dc220v, ≥ 8A Support 2-4 independent node output capability

Intelligent light control unit

Output mode: switch type, realize local and remote control of lighting Wall mounted / 2U rack mounted Using brand devices to ensure reliability Size (mm): 480mm long × 85mm wide × 340mm deep

Intelligent water pump control unit

Output mode: switch type, realize the linkage control of water pump Wall mounted / 2U rack mounted, Using brand devices to ensure reliability Size (mm): 480mm long × 85mm wide × 340mm deep